Add Your Email to Receive Special Offers!

  Home > Copper Plated Bullets >

9mm-165 RN
  Quantity of 500
  Diameter: 0.356

  UPC: 819304010291

9mm 165 RN
9mm 165 RN
Quantity of 500
Diameter: 0.356

UPC: 819304010291


Product Code: XC9MM-165RN-B0500

X-Treme Bullets are proudly made out of the finest materials available in the United States in order to ensure performance delivered down range with each and every shot.  Our process starts with a lead billet that is extruded into wire. The lead wire is then swaged into a core. The cores are copper plated, then restruck once more. Though not common in the industry, this restrike process produces a bullet that is more uniform, with a more precise diameter and a smoother finish for a better shooting and better looking bullet.

Average Rating: 5 of 5 Total Reviews: 14 Write a review »

  0 of 0 people found the following review helpful:
165 gr. 9mm January 20, 2018
Reviewer: Mark Plummer from Vaughn, WA United States  
I have loaded over 3,000 of these in mixed brass with Federal or Remington primers for more then three years. My favorite load is 2.8 gr. of Red Dot with a OAL of 1.152. It fits in all my magazines and  makes between 128 and 135 power factor in all my handguns. It shoots reliably in my M&P Shield, STI 5" 1911 and my other 9's. Shoots well in carbines and has proven itself in IDPA and USPSA competition. Where  I always finish in the top 10.... from the bottom! But it is never the bullets fault! As other reviewers have stated, it is very soft. This is my favorite 9mm bullet. I always finish my loads with a Factory Crimp Die.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
Soft shooting and accurate out of a Shadow 2 December 8, 2017
Reviewer: Jay from Florida  
I shoot a CZ Shadow 2. I first tried loading to a COL of 1.185, recommended by a friend who shoots these. Passed the chamber check but, I couldn't load more than 4 or 5 in the magazine. I read that seating these to SAAMI max COL would swage the base of the bullet. At that point I had nothing to lose so I nudged it in little by little until it would clear the front of the magazine. I ended up @ 1.169 which is exactly SAMMI max. I'm using Speer nickle plated cases with Winchester small pistol primers. I settled on 2.6gn of Cleanshot (Shooters World... I love this stuff). It just makes PF but, if it were a big match I'd probably go 2.7, maybe 2.8gn just to be sure all the rounds meet minimum PF. The recoil is unbelievably soft and it's never been so easy or fast to get back on target. I've never shot as tight of groups as I do with this setup when shooting long strings of rapid fire. I can't wait 'til they go on sale again.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
Great bullets for shooting suppressed October 29, 2017
Reviewer: Ken from PA United States  
I love these heavyweights. I've pushed them pretty hard too and never had an issue.

To the reviewer who gave 2 stars: it really bothers me when someone gives a poor review that is undeserved. If your denting the bullets it's because you're doing something wrong, its not the fault of the bullet. Bell the case more and/or use a seating stem that fits the bullet better. With any plated bullet it's important to have a good fit, these especially.

Was this review helpful to you?

  0 of 9 people found the following review helpful:
Looks nice but it's very soft. September 30, 2017
Reviewer: Iric Viscarra from Honolulu , HI United States  
These bullets are nice and uniform but I was disappointed when i loaded it using my dillon 550 reloader..the tip of the bullet is always dented,i tried to load 20 rnds and the result is still the same.too bad I purchased 1500 rnds and I don't want to load these bullets anymore.

Was this review helpful to you?

  8 of 8 people found the following review helpful:
Great soft and quite load March 17, 2017
Reviewer: David C. from Salt Lake City, UT United States  
These bullets are very uniform. There is no 9mm round I enjoy shooting more than these over 3 grains of Titegroup. Due to the minimal recoil I am able to get back on target much faster than faster lighter bullets. Have had no reliability issues in my 4.5" XDM.

I do reload with mixed brass and some brass is thicker at the base which may cause a problem. I check all my loads with a chamber gauge, but I would at least recommend dropping any ones that required more force to seat in your barrel to make sure it chambers as the bullets are quite long.

Was this review helpful to you?

View All Customer Reviews

Copyright ©  X-Treme Bullets LLC. All Rights Reserved. Built with Volusion

Website Designed by Visual Marketing